Special track routing & interfaces

Custom stem routing, IEM/house outputs and USB multichannel interfaces for live backing tracks.

Search the full manual Watch pro audio videos

Special track routing

Open Settings → Special track routing to match stem names across your whole library — once — instead of muting or re-routing the same tracks song by song in the mixer.

Turn on Automatic routing. Under Special tracks, edit Click / Cue stem / SMPTE and your customs. BackTrackR compares each track’s name (from Edit / the filename) to your match lists. Matched tracks get pan, optional mute, optional hardware output, and — if you want — a shared strip look.

Routing sits on top of each song’s mix. Turn a profile off and that song’s saved mix comes back — the mix file is not overwritten.

Closing Settings re-scans the library only when routing rules changed (progress overlay on large libraries). Re-scan library for conflicts always walks songs and names the song and tracks.

Built-in profiles

  • Click — metronome for the drummer’s in-ears (default matches include klik, click, metronome, …)
  • Cue stem — spoken count-ins or section cues
  • SMPTE — timecode for lighting or video

Route click to IEMs while the audience hears only the backing through the house PA — no splitter workarounds. Built-ins default to Apply strip look on, so the mixer shows a clear KLIK / CUE / SMPTE channel.

Custom profiles

In the Special tracks list, tap Add custom (up to 32). Use these for regular music stems you want to control globally — not only click/cue/timecode.

Typical solo / duo / trio / band workflow:

  1. Name stems consistently across songs (e.g. Kick, Snare, Bass, Keys, Gtr).
  2. Add a custom profile per group (e.g. “Trio drums”) with those Match names in filenames (comma-separated aliases are fine).
  3. Leave Apply strip look off on mute groups so each track keeps its own name in the mixer (kick stays Kick, snare stays Snare).
  4. For tonight’s gig, turn Mute on for groups you are not using (e.g. mute drums + bass for a duo with keys only).
  5. Save — BackTrackR applies mute (or unmute) to matching tracks on every song. Flip Mute again when the lineup changes.

Why this helps: You keep a full multitrack library for every job, then switch Duo / Trio / Full band from Settings in seconds — without opening each song’s mixer. Mute is for setup before the show, not mid-song fader grabs.

Per-profile options

  • Match names — comma-separated; exact name or a token inside a longer filename (e.g. smpte 2-4 → SMPTE)
  • Apply strip look — when on, strip name / icon / colour override matched tracks (Click / Cue / SMPTE default on; customs default off for mute groups)
  • Profile name — always available; becomes Name on track strip when Apply strip look is on
  • Mute — library-wide mute on save; turn off to unmute those matches everywhere
  • Pan — Left / Center / Right chips on matched tracks
  • Output — Master (main mix) or a dedicated interface pair/channel when multichannel is available

Built-ins are checked first; then customs in list order — first match wins. At most two enabled customs may use hardware outs; extra customs stay on Master (mute-only customs need no reserved bus).

If something already uses an output you reserved for special tracks, use Re-scan library for conflicts and pick a new destination.

Audio interfaces

BackTrackR works with the iPad's built-in headphone output for rehearsal and small setups. For live rigs, a multichannel USB audio interface is recommended.

When to use an interface

  • Separate outputs for click/IEM and house mix
  • Balanced XLR outputs to a front-of-house mixer
  • Lower latency for live performance
  • Multiple monitor mixes for band members
  • Analog LTC chase input (dedicated In channel)

Connect your interface via USB. Under Settings → Audio & mixer you can see the active device, set preferred sample rate (44.1 / 48 kHz), IO buffer (2048 or 4096 samples), Meter refresh (Auto / 30–120 Hz), and Show system load in status bar. Stem routing options appear when a multichannel device is detected. Use 4096 when playback feels tight.